Greetings and seeking KJ wisdom

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

SmoothinWI

New Member
Joined
Sep 8, 2024
Messages
2
Reaction score
1
Greetings all, just bought our first KJ, its a 123,00ç mile 07 Liberty Limited. Typical rust, mechanically sound.
Needs ball joints for sure, any guidance on 2 inch lift while doing the suspension work appreciated.
I bought this thing to pull our clean TJ off the roads for winter. I know nothing about it until 2 weeks ago.
 

DadOSix

Full Access Member
Joined
May 20, 2020
Messages
834
Reaction score
477
Location
Cumberland, MD.
Greetings all, just bought our first KJ, its a 123,00ç mile 07 Liberty Limited. Typical rust, mechanically sound.
Needs ball joints for sure, any guidance on 2 inch lift while doing the suspension work appreciated.
I bought this thing to pull our clean TJ off the roads for winter. I know nothing about it until 2 weeks ago.
If it were me, i would not spend the cash for a lift, since the body is rusty. I have 2 of these. 04 and 06. Neither worthy of a lift imo.
 

KJowner

Full Access Member
Joined
Oct 20, 2022
Messages
1,497
Reaction score
871
Location
Uk
Weld it up first, it doesn't have a chassis so the rust massively affects the strength of the body.
 

SmoothinWI

New Member
Joined
Sep 8, 2024
Messages
2
Reaction score
1
Weld it up first, it doesn't have a chassis so the rust massively affects the strength of the body.
Tell me what you mean by "weld it up".
I bought this thing for a winter beater with a heater. Perhaps I will forget about lifting it and just spray foam the holes with Great Stuff and spray bomb the crap out of it. Spend some money on the brakes and suspension.
 

lfhoward

Wheel. Repair. Repeat.
KJ Supporting Member
Joined
Dec 9, 2012
Messages
2,449
Reaction score
2,711
Location
Philadelphia, PA
Can you post pics of your KJ? It would be easier to see what kind of structural issues the rust might be causing, if any.
 

KJowner

Full Access Member
Joined
Oct 20, 2022
Messages
1,497
Reaction score
871
Location
Uk
Tell me what you mean by "weld it up".
I bought this thing for a winter beater with a heater. Perhaps I will forget about lifting it and just spray foam the holes with Great Stuff and spray bomb the crap out of it. Spend some money on the brakes and suspension.
I mean the sills etc are structural, if you have major corrosion there it will have lost a lot of strength, they normally rot out there. Spray foam is not a good idea, it holds the water in there and makes it rot faster + it only adds the illusion of strength!
There are new panels available that will sort it out properly and give you a strong safe car that will give you years of winter service.
 

u2slow

Full Access Member
Joined
Mar 6, 2012
Messages
765
Reaction score
173
Location
BC
Ours had some rocker rust (holes), toward the rear, and it is lifted (10 years now). Has not been a problem - it is largely a daily-driver; not an offroad machine. The plastic rocker covers retained moisture and mud over the years. I cut off the rough stuff cleanly. Then used rust converter, primer, and rust paint along the bottom 5" or so. I know there are replacement full-length rockers to weld in, but I think I may form my own weld-in patches instead.

I chose the Teraflex spacer lift years ago. There are now knockoffs of that too
 

KJowner

Full Access Member
Joined
Oct 20, 2022
Messages
1,497
Reaction score
871
Location
Uk
The outer rocker is just a thin cover panel, inside is the heavier structural steel, I put some pictures on here of mine when I welded it up, the rust you see outside is tiny compared to the rust inside on the structural stuff, I had new inner sills folded up by a sheet metal shop so I could just chop all the rotten metal out and weld new in.
We have annual inspections so any structural rot take the car off the road.
 
Top