Lift kits and IFS parts

KingKJ · Sep 8, 2024

I've been reading about alot of different upgrades regarding the suspension of a jeep liberty with the cvs and control arm upgrades. I'm curious how much lift you can get out of the IFS if you go all out and upgrade all the control arms, cvs, etc. I would like to get at least 4 inches of lift and also improve the travel in my suspension and possible be able to squeeze in bigger tires. I would like to figure out just what it will take to get better articulation and lift so that I can decide on if I am going to regear without changing IFS to SFA or if it is best to just swap to SFA rather than mess with trying to get more lift out of the IFS.
FYI, I don't care how much work it will take to do the upgrades or anything, I'm going to Auto School and am figuring out what upgrades I can do to my jeep.

ikuo78 · Sep 9, 2024

JBA says it took 900 hours to create.
10" cradle down and 10" long arm.

Our Vehicles at JBA Offroad

rockcrawling.jbaoffroad.com

You must be registered for see images attach

KingKJ · Sep 9, 2024

holy crap that is alot of time XD
Idk if I wan't to go that in depth and keep it as IFS, I'm hoping it could be possible to get around a 5-6 inch lift but it sounds like stuff isn't made for the KJs anymore to do that so I'm kinda looking at what my options are to get as close to that as I can, I've heard of 4.5 inch lifts, but am just unsure what parts are needed including the cvs, control arms, etc.

KingKJ · Sep 9, 2024

I'm attempting to see how close to 33 inch tires I could fit, I'd love to run at least 33s but even that sounds like it won't be possible anymore due to parts not being made

ikuo78 · Sep 9, 2024

A man installed a 33-inch tire with just a 2-inch lift.

Project 2004 Liberty pickup

I finally got my first Jeep Liberty! Always wanted one and finally found the perfect one. 2004 Liberty, 4x4, automatic transmission and the coolest bumper I have ever seen. I think the craiglsist ad read something along the lines of: Liberty, runs and drives, 4x4 works great, daily driver...

www.jeepkj.com

joshgoble · Sep 11, 2024

KingKJ said:
I've been reading about alot of different upgrades regarding the suspension of a jeep liberty with the cvs and control arm upgrades. I'm curious how much lift you can get out of the IFS if you go all out and upgrade all the control arms, cvs, etc. I would like to get at least 4 inches of lift and also improve the travel in my suspension and possible be able to squeeze in bigger tires. I would like to figure out just what it will take to get better articulation and lift so that I can decide on if I am going to regear without changing IFS to SFA or if it is best to just swap to SFA rather than mess with trying to get more lift out of the IFS.
FYI, I don't care how much work it will take to do the upgrades or anything, I'm going to Auto School and am figuring out what upgrades I can do to my jeep.

how well can you weld?

KingKJ · Sep 11, 2024

Not al

joshgoble said:
how well can you weld

joshgoble said:
how well can you weld?

Not at all lol

joshgoble · Sep 11, 2024

KingKJ said:
That's going to be a slight problem if you want to lift one

KingKJ · Sep 11, 2024

yeah I figured, the more I look the more I see all the aftermarket parts just aren't there anymore for the Libertys

joshgoble · Sep 11, 2024

KingKJ said:
yeah I figured, the more I look the more I see all the aftermarket parts just aren't there anymore for the Libertys

Best to my knowledge there never was any thing larger than 4" lifts mainly because you have to relocate the upper control arm and then it's minimum 8¾" lift to 12 inches it is a pain especially when you get to relocate the the steering and length en the shaft from the steering wheel to the steering gear and range the mount and keep it from binding on the manifold. you will need access to an end mill and lathe. You will want to learn steering geometry and suspension geometry because you will run in to issues with the scratch pad and odds and ends of things that aren't commonly known.
.

KingKJ · Sep 11, 2024

joshgoble said:
Best to my knowledge there never was any thing larger than 4" lifts mainly because you have to relocate the upper control arm and then it's minimum 8¾" lift to 12 inches it is a pain especially when you get to relocate the the steering and length en the shaft from the steering wheel to the steering gear and range the mount and keep it from binding on the manifold. you will need access to an end mill and lathe. You will want to learn steering geometry and suspension geometry because you will run in to issues with the scratch pad and odds and ends of things that aren't commonly known.
.

I've heard jba used to seel 6 inch lifts but they have been discontinued

joshgoble · Sep 11, 2024

if they did I never seen one and don't know how they accomplished it without relocation of the uper control arms and the cv axle and angles won't allow more than 4 inches and even at 4 inches your flirting with disaster and better enjoying changing cv joints unless they build a drop down bracket for the front differential and risers for the steering to correct the geometry to keep from having horrible bump steer

joshgoble · Sep 11, 2024

joshgoble said:
if they did I never seen one and don't know how they accomplished it without relocation of the uper control arms and the cv axle and angles won't allow more than 4 inches and even at 4 inches your flirting with disaster and better enjoying changing cv joints unless they build a drop down bracket for the front differential and risers for the steering to correct the geometry to keep from having horrible bump steer

the tie rods needed the same angle as the cv axles

joshgoble · Sep 11, 2024

joshgoble said:
the tie rods needed the same angle as the cv axles

you can manage the brake line by rebending the steel break line and lowering the connection

joshgoble · Sep 11, 2024

the front suspension isnt the biggest problem actually isn't the hardest issue to address either the rear suspension is where my biggest issues were coming up with a disign that would function and hold is the biggest trick. So I found out after the fact I was breaking 1¼ high pressure pipeline flange bolts and rolling the rear end out of it a couple times. I was forced to put a center drag link /track bar in it. Something I was trying to avoid. but it worked never the less.

Lift kits and IFS parts

KingKJ

The Rock Spotter

ikuo78

Full Access Member

Our Vehicles at JBA Offroad

KingKJ

The Rock Spotter

KingKJ

The Rock Spotter

ikuo78

Full Access Member

Project 2004 Liberty pickup

joshgoble

Setting on 37x13.5x 17

KingKJ

The Rock Spotter

joshgoble

Setting on 37x13.5x 17

KingKJ

The Rock Spotter

joshgoble

Setting on 37x13.5x 17

KingKJ

The Rock Spotter

joshgoble

Setting on 37x13.5x 17

joshgoble

Setting on 37x13.5x 17

joshgoble

Setting on 37x13.5x 17

joshgoble

Setting on 37x13.5x 17

Similar threads

Random media

Latest posts

Staff online

Members online