Search results
-
K
Trouble Starting When Warm
Not sure if my novice input helps, it's just more evidence I suppose. Ever since I got my 05 3.7 KJ it's had random hot start problems. No more than once every 2 months in the summer never in the winter. I always start it with a little bit of gas if it doesn't want to start and it fires up and...- KJordan333
- Post #19
- Forum: KJ General Discussion
-
K
Parking lot
Just thought I'd add a few more! First one was walking out of best buy and a stock silver kj parked by me, maybe you can tell the difference... Second time was because I parked next to a stock kj just so I could see a difference...- KJordan333
- Post #126
- Forum: Post Your Liberty Pictures
-
K
Clutch/flywheel options
I actually just picked my car up from the shop with a stock luk clutch and flywheel so I guess I'll have to be happy with that. Although honestly, it feels like a whole different car! and for 1100 instead of the 1800 that the dealer wanted.- KJordan333
- Post #13
- Forum: KJ General Discussion
-
K
Clutch/flywheel options
I guess I just heard that it could not be machined so I'm getting a new one. But are there any options?- KJordan333
- Post #9
- Forum: KJ General Discussion
-
K
Clutch/flywheel options
I believe mine is actually a dual mass also so it can't be machined down so I'm getting a new one. But I was just curious if there were any options. Not exactly like a racing flywheel or anything like that, but are there any quality options that may be able to handle a little more.... use?- KJordan333
- Post #5
- Forum: KJ General Discussion
-
K
Clutch/flywheel options
So after my throwout bearing went back in my '05 sport this past month, I'm looking into a new clutch and flywheel as I understand that they both have to be changed or it will just chatter. But my real question is do I have any aftermarket clutch or flywheel options? I'm not trying to make the...- KJordan333
- Thread
- Replies: 36
- Forum: KJ General Discussion
-
K
Parts for a 4.10 regear
I think I'll just provide all my own gears that I'll buy off jeepinbyal. And does jeepinbyal also sell the truetrack locker for the 8.25?- KJordan333
- Post #32
- Forum: KJ General Discussion
-
K
Parts for a 4.10 regear
I know all this info was already listed, but the shop I'm looking at says that they'd put these in the front : High performance Yukon replacement ring & pinion gear set for Dana 30HD in Jeep Liberty, 4.10 ratio. - YG D30HD-410L It says super 30HD or something. So should I do that or just...- KJordan333
- Post #29
- Forum: KJ General Discussion
-
K
Parts for a 4.10 regear
I'm definitely sure I want to do a regear for the potential mileage change and just to make it easier on the car. And I'm getting all the parts except a carrier from jeepinbyal (even at slightly more cost), and then I think I'll have to have them put in at SFF customs to try to stay under...- KJordan333
- Post #27
- Forum: KJ General Discussion
-
K
Parts for a 4.10 regear
Sorry I have so little knowledge about this... Cardhu, I would need that bearing and seal kit and then those 4.10's are for the front as well? where do I get the rear parts? Can I just trust a shop to get the right parts?- KJordan333
- Post #7
- Forum: KJ General Discussion
-
K
Parts for a 4.10 regear
I do have the 6-speed manual so I will need the new carrier and I believe my earlier link is for the "super" dana 30. I was also told to get USA standard gears for the rear and of course yukon in the front. When I search for front gears should I be looking for just dana 30 or dana 30a/dana 30HD...- KJordan333
- Post #4
- Forum: KJ General Discussion
-
K
Parts for a 4.10 regear
Hi, I'm new to this forum, and I hope I'm not asking something that's been asked way too many times before, but I was looking for some help finding parts for a regear. I have an '05 KJ with the 3.7 and it's currently geared to 3.53 (stock). I'm in the process of getting parts for a regear to...- KJordan333
- Thread
- Replies: 32
- Forum: KJ General Discussion
