Forums
New posts
Search forums
What's new
New posts
New media
New media comments
New resources
Latest activity
Media
New media
New comments
Search media
Resources
Latest reviews
Search resources
Members
Current visitors
Log in
Register
What's new
Search
Search
Search titles only
By:
Current visitors
Menu
Log in
Register
Install the app
Install
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
klc
KJ Supporting Member
“It flies like a truck.”
·
From
PNW
Joined
Jan 14, 2022
Last seen
Today at 8:17 AM
Messages
599
Media
36
Reaction score
825
Points
93
Find
Find content
Find all content by klc
Find all threads by klc
Latest activity
Postings
Media
Albums
About
klc
replied to the thread
Transmission temperature sensor
.
Thanks. I missed that.
Thursday at 10:07 PM
klc
reacted to
ikuo78's post
in the thread
Transmission temperature sensor
with
Like
.
Regarding 42, there is a description and it is integrated with the transmission range sensor. It looks like a big job. It would be...
Thursday at 10:04 PM
klc
posted the thread
Transmission temperature sensor
in
KJ General Discussion
.
Where is it? I think mine might be a bit off. Sometimes the warning light comes on when I’m climbing a mountain pass. But there has...
Thursday at 6:31 PM
klc
replied to the thread
Transmission Skid Plate DIY
.
Gosh, yes. Any time someone has claimed to have a transmission plate, they show me a transfer case plate.
Thursday at 4:13 PM
klc
reacted to
dtennes's post
in the thread
How to rebuild and install a wiring harness for either fuel injectors of ignition coils
with
Like
.
10. Illustrations where helpful I am attaching a ".pdf" file that outlines everything with some illustrative images. >>>NOTE<<< The...
Wednesday at 2:49 PM
klc
reacted to
ReniTheRenegade's post
in the thread
Installing JBA Control Arms
with
Like
.
I really appreciate the responses, yall! I'm replacing suspension and I&O tie rods too so everything is undone. Persuasion by force...
Monday at 9:25 PM
klc
reacted to
seafish's post
in the thread
What did you do to your jeep today?
with
Like
.
Today I replaced the rear differential speed sensor in order to keep the odometer from intermittently dropping out. While I had...
May 11, 2024
klc
reacted to
seafish's post
in the thread
What did you do to your jeep today?
with
Like
.
Here a few pix of the soldered, shrink wrapped and loomed fix ... only took about an hour which also included brushing down the dirt...
May 11, 2024
klc
reacted to
KJowner's post
in the thread
2007 Liberty won’t allow me to put in gear
with
Like
.
Check the clutch fluid level, if its low look for the leak, if its ok you could put axle stands under the rear and start it up in gear...
May 11, 2024
klc
replied to the thread
2007 Liberty won’t allow me to put in gear
.
First guess would be the clutch slave cylinder, though I’m not familiar with the manual transmission. I did have to replace the clutch...
May 11, 2024
klc
reacted to
ikuo78's post
in the thread
What did you do to your jeep today?
with
Like
.
I washed my car for the first time this year and went on a short trip. The sun in May is very strong, Even an old body looks beautiful.
May 11, 2024
klc
reacted to
NORVIN's post
in the thread
Differential vs. Transmission Speed Sensors
with
Like
.
Yes. Not "shavings" but "specks"/"particles" were what I saw on the speed sensor. I drove to a somewhat nearby AutoZone that had the...
May 11, 2024
klc
reacted to
Ksat's post
in the thread
Random multiple error codes and noise after engine replacement.
with
Like
.
At least on my '06, the PCM cuts injector control on a misfiring cylinder, not ignition control. The is an to prevent catalyst damage. A...
May 11, 2024
klc
reacted to
Phil2020's post
in the thread
How do I access blend door actuator?
with
Like
.
Thank so much for your reply! Mine is also a 2002 Liberty 3.7 Thought there were 2 actuators for the heating blend doors. One for the...
May 6, 2024
klc
reacted to
dtennes's post
in the thread
Random multiple error codes and noise after engine replacement.
with
Like
.
The PCM is a "living" machine. It is constantly receiving and interpreting feedback information from all of your sensors... plus the...
May 5, 2024
Loading…
Loading…
Loading…
Loading…
Random media
Latest posts
Yet another Engine Swap
Latest: WheelNut
Today at 11:44 AM
KJ General Discussion
K
Manipulated PCM
Latest: KJowner
Today at 2:43 AM
CRD KJ's Section
Dash kit suggestions?
Latest: Luke
Today at 1:34 AM
KJ General Discussion
What did you do to your jeep today?
Latest: sota
Yesterday at 10:40 PM
KJ General Discussion
Portal hubs
Latest: duderz7
Yesterday at 9:07 PM
KJ General Discussion
Members online
lfhoward
JasonTheOverlander
Members
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
Accept
Learn more…
Top