tjkj2002
Full Access Member
- Joined
- Dec 17, 2006
- Messages
- 10,612
- Reaction score
- 41
To make room for the front driveshaft.With IFS the front driveshaft never moves(up/down,left/right) but with the SFA the driveshaft moves alot and needs clearance.
It sits level
- Thread starter tjkj2002
- Start date
Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.
tjkj2002
Full Access Member
- Joined
- Dec 17, 2006
- Messages
- 10,612
- Reaction score
- 41
Well been working on the belly pan,should have it done by Thursday and ready to paint.It's a 3 part belly pan and the pics below is just of the main piece(not 100% finished),the 2nd piece bolts to the main piece and extends forward to protect the trans pan and the 3rd is just a plastic filler(you will see what I mean when finished and installed).All material is 1/4" thick.
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
Looks great Troy!
tjkj2002
Full Access Member
- Joined
- Dec 17, 2006
- Messages
- 10,612
- Reaction score
- 41
Been driving it for 2 weeks now,got about 350 miles on the SFA just breaking in the gears and t-case.Already drained and refilled the t-case and in about 150 miles will drain and refill the rear diff,the front diff will be okay for some time since I now have lockouts and the front diff does not spin at all unless I lock the hubs in.
kj924
Administrator
Nice Troy. Does the front diff get separated at the Atlas? That saves a lot of wear and tear on the front.
tjkj2002
Full Access Member
- Joined
- Dec 17, 2006
- Messages
- 10,612
- Reaction score
- 41
It drives real good now,been working the little bugs out,nice and firm.The only drawback is the decreased turning radius when the R&P steering was replaced.No offroad yet since it is not finished and no offroading till at least 500miles since I need to break in the rear gears at least properly.
The manual front hubs separate the front diff axles from the front hubs,thus with no power being sent to the front driveshaft(with the t-case in 2wd) the front driveshaft and front diff gears/axles will not turn.Though the AtlasII is a twin stick t-case with one shifter for the front output and one shifter for the rear output.
ThunderbirdJunkie
Bronze Supporter
So you can put the Atlas in front wheel drive?
tjkj2002
Full Access Member
- Joined
- Dec 17, 2006
- Messages
- 10,612
- Reaction score
- 41
FWD low only.
ThunderbirdJunkie
Bronze Supporter
Sweet
tjkj2002
Full Access Member
- Joined
- Dec 17, 2006
- Messages
- 10,612
- Reaction score
- 41
Supposedly you can remove the front output shift rail and grind down some stop so you can engage 2wd hi only,but doing so would remove the failsafe from going into front hi/rear low and front low/rear hi also.
ThunderbirdJunkie
Bronze Supporter
You could always put it in 4 hi and pull the rear driveshaft to break in those front gears 
tjkj2002
Full Access Member
- Joined
- Dec 17, 2006
- Messages
- 10,612
- Reaction score
- 41
Can't,I'm running CTM u-joints in the front axles,they will not last long for daily driving since they have no needle bearing in them(just ment for extreme strength for offroad occasional offroad use).Kinda a trade off that I can live with since when a $25 u-joint will ruin my $650 set of alloy axles when that u-joint breaks where as the axles will break before the CTM u-joint will(if properly maintained),basically putting the weak link in a easy to replace WARN manual lockout which are cheap and lifetime warrantied.You could always put it in 4 hi and pull the rear driveshaft to break in those front gears
tjkj2002
Full Access Member
- Joined
- Dec 17, 2006
- Messages
- 10,612
- Reaction score
- 41
Bellypan is completed and installed,one heavy ****
Super Skinks are also done but the paint is drying and will be installed tomorrow or Thursday.
You must be registered for see images
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
Super Skinks are also done but the paint is drying and will be installed tomorrow or Thursday.
Troy, you are gonna have to put that monster on a truck scale when you are done to see what it weighs all modded up....you will be over 5,500lbs easy before you even get in it or put recovery stuff and tools in it.......maybe 0ver 6k even.
Dave
Dave
tjkj2002
Full Access Member
- Joined
- Dec 17, 2006
- Messages
- 10,612
- Reaction score
- 41
I started out at 5500lbs before the SFA
,I'm betting on around 6200lbs-6500lbs when fully outfitted.And yes the scale I will go(as planned) once it is 100% complete.
Hey Troy, name one part on your Jeep that is stock...I can't think of one!
Hey Troy, name one part on your Jeep that is stock...I can't think of one!
I don't think he changed the steering wheel.....yet.
Dave
tjkj2002
Full Access Member
- Joined
- Dec 17, 2006
- Messages
- 10,612
- Reaction score
- 41
The steering wheel has been modifiedDave Quote:
Originally Posted by Hoosierjeeper
Hey Troy, name one part on your Jeep that is stock...I can't think of one!
I don't think he changed the steering wheel.....yet.
Dave
.The engine is stock,the trans is 100% stock(never touched yet besides maintenance),electric cooling fan is stock(along with the resister),all of the HVAC is stock(even OEM R134A in it and it blows very cold),and heck all 4 window regulators are the originals from the factory
.But that's about it.
How much modding could you do on a window reg???
tjkj2002
Full Access Member
- Joined
- Dec 17, 2006
- Messages
- 10,612
- Reaction score
- 41
Nothing really I guess.How much modding could you do on a window reg???
