Search results
-
2003 Jeep Liberty gas tank issue.....
Number 11 is suspicious.- ikuo78
- Post #2
- Forum: KJ General Discussion
-
New Member question about front drive shaft in 2007 Liberty
You can add grease by carefully removing the thin metal cap with a small flathead screwdriver or by removing the boot. I think boot bands that are crimped in a Z-shape are the least likely to leak. If you loosen the thin metal cap evenly around the entire circumference while turning it, it will...- ikuo78
- Post #4
- Forum: Introductions
-
New Member question about front drive shaft in 2007 Liberty
It seems that because it was left in the removed state, the internal seal was not crimped and it just seeped out. I think it's okay if you install it. If too much grease comes out, you will need to add more grease. There is a possibility that grease may be temporarily spread after installation...- ikuo78
- Post #2
- Forum: Introductions
-
3-5 inch lift
If you jack the car so that the suspension is extended, you can check the location of the collision. There may be individual differences, but when using a spacer lift, the shock length will be longer by the spacer, so the down travel will increase and in most cases the knuckle will hit the coil...- ikuo78
- Post #32
- Forum: KJ General Discussion
-
Mystery P0300 root cause?
The easiest way to tell that the PCM is failing is when the condenser is leaking. If this is not the case, the only option is to perform a wiTECH2 diagnosis, but the price may be similar to that of a rebuilt product.- ikuo78
- Post #32
- Forum: KJ General Discussion
-
3-5 inch lift
As for the front, the stock down travel is just under 120mm. If you set this to 140mm, the upper arm or knuckle will hit the spring. In other words, the additional lift that can be obtained by extending the shock length with spacers etc. is about 20mm. It seems that this problem can be solved by...- ikuo78
- Post #28
- Forum: KJ General Discussion
-
3-5 inch lift
ARB https://arbusa.com/ https://store.arbusa.com/search-result Year=2003&Make=Jeep&Model=Liberty&Submodel=Renegade- ikuo78
- Post #10
- Forum: KJ General Discussion
-
Mystery P0300 root cause?
I'm sure fuel pressure may have been the trigger for activating ASD. Fuel pressure may be rising slowly. I think you should check in this order: Pump-Relay → Pump-ASSY → ORVR.- ikuo78
- Post #28
- Forum: KJ General Discussion
-
Mystery P0300 root cause?
I think the coil, injector, and O2 sensor heater were powered by the ASD relay. Has the relay deteriorated? Usually, if a thread is left up for a week, no one will see it.- ikuo78
- Post #27
- Forum: KJ General Discussion
-
Mystery P0300 root cause?
It's a good idea to fix it and use it. So am I. These types of problems tend to take a long time to resolve. It confuses people because it sometimes heals once. I would appreciate it if you could post if there is any progress. If you keep posting and put it in the "New Posts" section, it will...- ikuo78
- Post #22
- Forum: KJ General Discussion
-
Mystery P0300 root cause?
It's about possibility. The conditions that may indicate a canister failure are described above. I think you can think about it by recording the correlation between live data of purge pressure and intake pressure while driving. I've never done it though. It appears that the Liberty's fuel...- ikuo78
- Post #20
- Forum: KJ General Discussion
-
Mystery P0300 root cause?
If the canister cracks, it will breathe in the atmosphere directly. Only when the valve is open. Listen and visually check. If there is a blockage in the evaporation system, the pressure in the fuel tank will be disturbed. As a result, fuel pressure becomes unstable. In Liberty's case that...- ikuo78
- Post #16
- Forum: KJ General Discussion
-
Mystery P0300 root cause?
I guess the remaining mechanical possibilities are below. ・pcv ・Throttle butterfly play ・Canister deterioration ・Cam chain tensioner- ikuo78
- Post #14
- Forum: KJ General Discussion
-
What did you do to your jeep today?
I use a gel puncture repair kit like the cars sold these days. I've never used it, so I'm a little unsure. So I pay about $25 a year for towing service, which is free up to 20km.- ikuo78
- Post #26,158
- Forum: KJ General Discussion
-
Lift kits and IFS parts
A man installed a 33-inch tire with just a 2-inch lift. https://www.jeepkj.com/threads/project-2004-liberty-pickup.76169/- ikuo78
- Post #5
- Forum: KJ General Discussion
-
P2181-Cooling System Performance
I don't know the specified value, but if you put it in 90℃ hot water and the resistance is the same, it's broken. I think it will drop to about 0.5KΩ or less at 90℃. I forget if the gauge and ECU use the same sensor. Is the gauge also low? I think it's unlikely since it's summer. If you can...- ikuo78
- Post #2
- Forum: KJ General Discussion
-
Lift kits and IFS parts
JBA says it took 900 hours to create. 10" cradle down and 10" long arm. https://rockcrawling.jbaoffroad.com/trail/our-vehicles-at-jba-offroad- ikuo78
- Post #2
- Forum: KJ General Discussion
-
09 Won't Idle, No Codes
Oops KK has EGR. EVAP is a misunderstanding. I edited the above and deleted it. Please ignore.- ikuo78
- Post #18
- Forum: KK General Discussion
-
09 Won't Idle, No Codes
It's great that the problem has been clarified.- ikuo78
- Post #16
- Forum: KK General Discussion
-
Codigos p0430 y p0420
The OBD2 code does not seem to depend on the car model, so the code indicates a decrease in the efficiency of the catalyst system. P0420 is bank 1. P0430 is bank 2. Does the motor work properly?- ikuo78
- Post #5
- Forum: KK General Discussion
