Search results
-
Settled OME front springs and struts
The tire looks a little worn in that first picture, are the cords showing?- first&lastKJ
- Post #17
- Forum: Lift Kit Discussion
-
What did you do to your jeep today?
I was looking around under the hood of the 02 and found the EVAP test port was loose. I tightened it about one turn. The CEL has been on for a few years due to P0442 code (Evaporative Emission Control System Leak Detected). I hope this was the reason why.- first&lastKJ
- Post #18,716
- Forum: KJ General Discussion
-
Been around but never introduced properly
I would be happy to get to 250k with ours. Keep us updated on the 1 million mile goal.- first&lastKJ
- Post #2
- Forum: Introductions
-
i bought a jeep
Welcome to the forum, she looks clean and well taken care of.- first&lastKJ
- Post #2
- Forum: Introductions
-
P0340 code
It took me a few tries to get a reading from two of the three leads on the sensor. Meter set on OHMs 2000k, reading was 1770. Turned on hair dryer and it started to drop. Went down to 650 and fluctuated a little from there. Turned hair dryer to cool and the reading began to climb slowly.- first&lastKJ
- Post #12
- Forum: KJ General Discussion
-
JBA LIFTS
It does not look like JBA is going to carry OME, Bilstein, Rancho or OEM since is out of stock on almost all of these items. I thought he was going to concentrate on just A-arms.- first&lastKJ
- Post #24
- Forum: Lift Kit Discussion
-
JBA LIFTS
So who is the new go to for OME lift kits for the kj?- first&lastKJ
- Post #22
- Forum: Lift Kit Discussion
-
P0340 code
Not sure how to do it, I may have to look on you tube.- first&lastKJ
- Post #10
- Forum: KJ General Discussion
-
P0340 code
I replaced the cam sensor tonight with a mopar one. I cleaned the plug with some CRC electronic cleaner, applied some dielectric grease to the plug and hooked up the battery, hope this helps.- first&lastKJ
- Post #8
- Forum: KJ General Discussion
-
P0340 code
Ok thanks. The PCM is on the drivers side correct? Whats the one on the pass. side? I did unplug the cam sensor and clean plug and sensor. It was covered with oil and 17 years of grime. I plugged it back in, hooked up the negative battery cable and started it up. I took it for a drive everyting...- first&lastKJ
- Post #6
- Forum: KJ General Discussion
-
P0340 code
I was doing some reading and it seems the p0340 could indicate a problem was detected in the camshaft position sensor circuit. So it could be the sensor itself, wiring, or PCM. P0340 could mean a wire or a connector in the circuit is broke, grounded or shorted. The camshaft position sensor...- first&lastKJ
- Post #4
- Forum: KJ General Discussion
-
P0340 code
Two times in the last few days while running around in the wifes 02 it would not start. We had to wait for a bit then try again and it started right up. When we got home I turned the ignition on and off three times and got a P0340 code. Guess I will replace the camshaft position sensor. Should I...- first&lastKJ
- Thread
- Replies: 13
- Forum: KJ General Discussion
-
What did you do to your jeep today?
Yep, bulk mulch on the first trip. Second trip was to wal mart and got 16 bags for $1.00 each on clearance. Most had rips or holes in them.- first&lastKJ
- Post #18,707
- Forum: KJ General Discussion
-
JBA LIFTS
CB Engineering makes some that look very close to the JBA's Adjust-A-Strut Coilover.- first&lastKJ
- Post #14
- Forum: Lift Kit Discussion
-
What did you do to your jeep today?
Hooked up the trailer and hauled two loads of mulch for the wife.- first&lastKJ
- Post #18,702
- Forum: KJ General Discussion
-
What did you do to your jeep today?
Worked it a little, drove it and took some pictures.- first&lastKJ
- Post #18,690
- Forum: KJ General Discussion
-
Actual Lift Amount - Lets Compare Fender Heights
I used the 9 year old Rustys front and rear lift springs off my wifes 02 with new Bilstein shocks. In the rear I added one extra upper isolator per side. Front also has the 1/4'' spacer plate. Front 21.5, driver side maybe a hair lower. Rear 21.5.- first&lastKJ
- Post #339
- Forum: Lift Kit Discussion
-
-
Alignment help
I think it was worth it either way. The JBA's are made really good and the ball joint looks so much happier than the OEM's did with the lift.- first&lastKJ
- Post #34
- Forum: KJ General Discussion
-
What did you do to your jeep today?
Took my 07 to the alignment shop. Looks like it's good to go this time.- first&lastKJ
- Post #18,687
- Forum: KJ General Discussion
