Search results
-
K
A/C Compressor will not run after dash removal
What valleyrome92 said. Run a jumper wire to the clutch on the compressor see if it clicks on. If it engages, don't let it run for long without checking static and dynamic pressures 1st.- Ksat
- Post #14
- Forum: KJ General Discussion
-
K
06 liberty 4x4 kj running rich.
That is an understatement! Do yourself a favor and buy an O2 plug extension for that side, so if you ever have to mess with it again, it will be a million times easier to unplug in the future. I did that myself a few years back in order to save myself a lot of cussing down the road. I can try...- Ksat
- Post #3
- Forum: KJ General Discussion
-
K
Wearing out rear pads over fronts.
Might be best to replace the master cylinder. They're cheap enough and not too hard to install.- Ksat
- Post #10
- Forum: KJ General Discussion
-
K
2003 Liberty 3.7L sport, Reman engine from Tri-Star, p0304 code
I just mean when the engine got up to temperature, a bad connection in a wire going to a fuel injector got worse and the injector stopped working. When things cooled down, the resistance in the wire lessened and it started working again. Have you tried noting the color of the wires that...- Ksat
- Post #21
- Forum: KJ General Discussion
-
K
Power window relay wire
You're a saint. Thanks for catching that. Yea, I have do have a power sunroof. I never use it, so I don't know if it lost power like the windows did originally or if it had that delay feature. The jumper wire I added was hard enough in itself to install, so I think I'll just suck it up and live...- Ksat
- Post #9
- Forum: KJ General Discussion
-
K
Problem with speed sensor cable
What year is your Jeep? Is the speedo working correctly? I don't know much about the VSS, but I read you're supposed to be getting 12V on one of the wires at the sensor with KOEO. If no power is present, you may want to check to see if any fuses have blown. A problem with the wiring going to and...- Ksat
- Post #2
- Forum: KJ General Discussion
-
K
High Voltage at Kickdown/High RPM.
Not sure it'd be helpful, but I found this: "The amount of DC current produced by the generator is controlled by EVR circuitry contained within the Powertrain Control Module (PCM). This circuitry is connected in series with the generators second rotor field terminal and its ground. Voltage is...- Ksat
- Post #5
- Forum: KJ General Discussion
-
K
Power window relay wire
It's a 2006. Like I said, the schematic I found on the '06 manual seems to say the same thing yours' did, though: that power goes straight from the window relay to the switch. No stopping anywhere. I found the diagram below on Fixya.com. The relay is in a hard to access spot, pretty far up...- Ksat
- Post #6
- Forum: KJ General Discussion
-
K
2003 Liberty 3.7L sport, Reman engine from Tri-Star, p0304 code
You might want to do a compression test in #4 just to confirm you have the proper pressure there. Remember to disconnect coil primary and floor the accelerator and crank for about 5 seconds when you do the test. Another possibility is you have an intermittent bad connection in the wires going...- Ksat
- Post #14
- Forum: KJ General Discussion
-
K
Dash lights flashing
Have you had your battery tested? If it checks out, test for a parasitic drain about an hour after key-off. 85 mA or lower seems to be what's considered normal. If it's more than that, you have a problem.- Ksat
- Post #4
- Forum: KJ General Discussion
-
K
Power window relay wire
Thanks for the reply. Yea, the 2006 manual shows the same thing, too, but that's obviously not the case because after the ignition is turned off (and the window relay shuts off with it) power continues to be supplied until the door gets opened or the system times out. If power was supplied...- Ksat
- Post #4
- Forum: KJ General Discussion
-
K
Fresh P0174 code...
What's FLAPS? Are you able to check the fuel trims? This would help confirm if the problem has been corrected. Running too rich or lean can cause additional problems (fuel wash, cat damage, etc).- Ksat
- Post #7
- Forum: KJ General Discussion
-
K
Converting from electronic to clutch fan
A mechanical fan alone won't cut it. You either need to have both or a solid electric one. I have the tow package with both fans and when my electric fan stopped working, on hot days at idle the mechanical could neither keep the engine from overheating nor keep the condenser cool enough, which...- Ksat
- Post #5
- Forum: KJ General Discussion
-
K
Power window relay wire
Would anyone know if the power coming from the power window relay makes a stop at the body control module before heading to the power window switch? I'm wondering since I noticed power to the relay gets cut as soon as the ignition is turned off, yet the windows will still function (after a set...- Ksat
- Thread
- Replies: 8
- Forum: KJ General Discussion
-
K
front end alignment
Camber is adjusted via 2 bolts on the lower control arms. I think whether or not you need new springs depends on how low your ride is sitting right now. I've never adjusted it on the lib, but typically there's a limit to how far you can push it positive (or negative). Sometimes there are cam...- Ksat
- Post #4
- Forum: KJ General Discussion
-
K
Rubber Strip; Where's it go?
This apparently fell on the ground after the driver's side door was opened. Anyone recognize where it goes? It's about 2ft long, I think.- Ksat
- Thread
- Replies: 2
- Forum: KJ General Discussion
-
K
Live data p0172 p0175
Glad you got it sorted out and my apologies for not getting around to doing that test on the PCM signals.- Ksat
- Post #67
- Forum: KJ General Discussion
