Search results

  1. E

    2005 AC Help - What am I doing wrong?

    ? The plugs sealing the ports? Yes, these were removed. Not sure what you're talking about.
  2. E

    2005 AC Help - What am I doing wrong?

    The dryer was replaced.
  3. E

    2005 AC Help - What am I doing wrong?

    Or, do you think I could just get by with vacuuming the system and a recharge?
  4. E

    2005 AC Help - What am I doing wrong?

    @Ksat - I only flushed the Evaporator, The short all metal line from the Evaporator to the Dryer IN port, and the Suction line (Line from Dryer out to Compressor.) Everything else was brand new installed. Well, I was able to spend a little time with it this morning to try and see if I could...
  5. E

    2005 AC Help - What am I doing wrong?

    Ok 2005 3.7L. Bought used a couple of years ago. AC didn't work and I could smell coolant in the truck. Replaced everything on AC system (All parts new) and heater core. Evacuated and recharged AC system worked fantastic. Within a couple of months, AC stopped getting cold. Attached gauges...
  6. E

    DIY-PCV-TSB

    I know this is an old thread but I have a question, what PCV valve (part #) are you putting in place of the crank case breather fitting in the back left of the motor?
  7. E

    Front Turn Signals -Help Me

    You will most likely need to trace the wires from the turn signal into the vehicle. It was probably cut somewhere during the collision. Reconnect the splice color for color and make sure to cover and seal any bare wires.
  8. E

    Power Steering Pump Questions?

    Thanks for the answers gang! I did a whole bunch of degreasing to try and find the leak and I'm not sure now its from the PS pump or lines. I've also checked the fluid level a couple of times and its stayed the same so I'm kind of still looking. With all the cleaning I'm thinking maybe its an...
  9. E

    Power Steering Pump Questions?

    Hey gang, noticed some leaking on the garage floor and followed it to the Power Steering. I'm thinking its either the reservoir or the pump, can't tell with it on so I pan on pulling it off to see for sure. Is there a replacement gasket to go between the reservoir on the pump? Part#...anyone...
  10. E

    ElecTape's Deep Beryl Green Build Thread

    I just followed the body lines on the hood, pretty easy. Thanks though for the compliments.
  11. E

    ElecTape's Deep Beryl Green Build Thread

    I did not precut the vinyl for hood wrap. It's actually quite easy to do. You'll need some knifeless cutting tape. Clean your surface where you'll be wrapping, and apply the knifeless tape in your design, make sure the knifeless tape is sticks out so you can start it. Also if you are not...
  12. E

    ElecTape's Deep Beryl Green Build Thread

    Thanks! The Dash isn't all that hard if you take your time and be patient. I'd suggest taking pictures along the way and marking screws. Just think of all the money you save doing it yourself too.
  13. E

    ElecTape's Deep Beryl Green Build Thread

    With the seat skins washed and clean I can now reassemble my two front seats and add my seat heaters. Started with one of the seat backs. Back together. Now for the bottom. Add the cover. Then its time to assemble the seat and add the wiring for the seat heaters. All nice and tidy...
  14. E

    ElecTape's Deep Beryl Green Build Thread

    Once the dash was all back together, I took the opportunity to pull the carpet out to replace it. I ordered a replacement carpet kit which arrived and was the wrong color. Argh! It also was not at all what I expected, no padding, the molding was not right and lots of other issues. So I sent...
  15. E

    ElecTape's Deep Beryl Green Build Thread

    Ironically this is a good time to change sparkplugs too. Since you've pulled the coolant overflow you can get to the 2 rear plugs on the passenger side. With the Heater Core out You'll need to take out a ton of screws to separate it into two halves. Take the time to clean the inside out...
  16. E

    ElecTape's Deep Beryl Green Build Thread

    So some of you remember that I noticed after I fixed the AC that I had a smell of Antifreeze when running the heat in the Liberty. I also occasionally got a steamed up windshield. Well these are the signs of a bad heater core. This is not a fun job to do since you have to pull the dash pretty...
  17. E

    ElecTape's Deep Beryl Green Build Thread

    Ok so its been a bit since I gave an update. So I recently added the factory Tow hooks to the front. If you haven't done this, its not real hard to do it just requires you to pull off the front bumper cover. So after the cover is off you'll need to remove these boxes in the image below...
  18. E

    Adding 2002 Steering wheel Controls to a 2005

    Thanks for all the help gang. Got it figured out! YEAH! The links above were great! I also stumbled across this old thread too: HOW TO: Install Steeringwheel radio controls on your Liberty | Jeep KJ and KK Liberty Forum So let me answer my questions from above: What did I actually need...
  19. E

    Adding 2002 Steering wheel Controls to a 2005

    Just have some quick questions. Luckily I was at my buddy's Junkyard today looking for a couple of Visor clips and I ran into a 2002 Liberty Limited that had the steering wheel audio controls. I decided to pull the following: Rear Housing trim Left & Right Audio Buttons Harness Both Cruise...
  20. E

    Limiting turning radius

    Well Thanks for all the help. Come to find out they forgot to tighten some stuff down and the sales lady didn't know it wasn't done when it was let go. Luckily nothing happened, and I caught it was odd immediately. All fixed and no rub and she drives beautifully!

Random media

IMAG1792
DSC05180
Micheline ATX tires and VTek "Off Road" Wheels
side
20150223 114302
hound
Brush Guard
image cleaned her to day
Design is a cross between two different sliders I really liked.

Latest posts

Members online

Total: 362 (members: 2, guests: 360)
Top