Search results
-
D
2003 Liberty no crank no start and stuck in gear
The ignition switch is a known problem in the Liberty...If you strong armed the key removal you may have damaged the linkage between the key tumbler and the actual ignition switch,,, Take a look at this video... https://www.youtube.com/watch?v=PpjnAS_-IRc Hope this helps... Dave- daves06lrenegade
- Post #7
- Forum: KJ General Discussion
-
D
Backup Camera Install - Looking for Reverse Wire
Look for a white/gray wire at the rear lamp(s)... That is the back up lamp feed... Dave- daves06lrenegade
- Post #20
- Forum: KJ General Discussion
-
D
Brake lights, turn signal , and hazard light not working
I just went through the "no turn signal" problem and did a youtube search... The video said that the hazard switch assembly was bad... I picked up two of these switches at my local pull-a-part yard and I still had no turn signals... I checked the hazard fuse (#11) and it was OK and the hazard...- daves06lrenegade
- Post #5
- Forum: KJ General Discussion
-
D
Worthy of fixing?
I also "see" you are in Charlotte N.C. ....N.C. is the home of "Pull-A-Part" and you probably have a rust free Liberty... I believe you have a good candidate for some rebuilding fun... An engine hoist and a load leveller from Harbor Freight figured into the cost will only add $200+ to the...- daves06lrenegade
- Post #18
- Forum: KJ General Discussion
-
D
Worthy of fixing?
Find a local pull-a-part yard and a Liberty that was hit bad in an accident (side/back)...Then look for an oil change sticker on the windshield with mileage and showing that the car's oil was changed before the accident... Take your breaker bar and socket and turn the engine over...Look under...- daves06lrenegade
- Post #17
- Forum: KJ General Discussion
-
D
No Cruise Control
The cruse control module uses a vacuum line to move the diaphragm... On my 2006 Liberty I found the plastic hose that fed this module was worn through allowing a vacuum leak...I repaired the line and the cruse was once again functional... Dave- daves06lrenegade
- Post #14
- Forum: KJ General Discussion
-
D
Finally...
Billwill... My "job" went away back in 2009 when our country went from repairing electronics to the Chinese "throw away" mind set... I have been involved in Consumer Audio Consumer Video Commercial and Industrial Video then service for large commercial multimedia accounts... All areas stopped...- daves06lrenegade
- Post #5
- Forum: KJ General Discussion
-
D
Finally...
Since I got my 2006 Liberty Renegade as "salvage" back in the start of Summer I have been fighting to locate wiring information (the number 8 (wiring) section was missing in all of my downloads).. I found a download that had it... I had to rewire the area going to the transmission and the...- daves06lrenegade
- Thread
- Replies: 4
- Forum: KJ General Discussion
-
D
Who has usable schematics for an 06 Liberty?
The title says it all... I have a 2006 Liberty Renegade that had a tunnel fire... Got that pretty much resolved but dome lights and door ajar switches have problems as well as the back door "glass" switch light and the rear wipers ( I think related to the glass switch)... I have found the...- daves06lrenegade
- Thread
- Replies: 0
- Forum: KJ General Discussion
-
D
Key stuck in ignition (and the fix)
I had this problem recently and I found by removing this cable at the steering lock assy (yellow push in connector)... I could remove the key...I could car less what position the shift lever is in when I remove the key... Now if I could only find schematics for the dome light circuitry, door...- daves06lrenegade
- Post #34
- Forum: KJ General Discussion
-
D
Jeep Liberty Replace Door Plastic Swap
i have a 2006 Liberty Renegade that had rusted out doors on the passenger side an came across the same problem...these are "one time" plastic rivets... To remove them drill out the center pin... Replacements are available (with the tool) at Harbor Freight.. After removing the rivets you have to...- daves06lrenegade
- Post #3
- Forum: KJ General Discussion
-
D
How to: Replace HVAC blend door actuator
Just some extra info on pulling the dash on a 2005-2006 Liberty... You won't be able to remove the dash until you remove two bolts UNDER where the two bolts that hold the steering shaft in place are located.... these two bolts go into the aluminum brace and are very hard to find.... They thread...- daves06lrenegade
- Post #21
- Forum: How To
-
D
Adding a true water temperature gauge?
Has anyone added a true water temperature (not the idiot gauge in the cluster)... I would like to add that gauge and also an oil pressure gauge... Any thoughts?- daves06lrenegade
- Thread
- Replies: 21
- Forum: KJ General Discussion
-
D
spongey brake pedal
If you have antilock brakes (ABS) there may be air in the ABS module... when I got my 06 3.7L Liberty the left rear brake line somehow got wrapped around the front driveshaft and ripped the line out of the ABS module... There was air in the whole system... The regular bleeding of the brake...- daves06lrenegade
- Post #11
- Forum: KJ General Discussion
-
D
Help to remove the front drive shaft
I have a 2006 Renegade that I also had problems removing the drive shaft... You need to remove the 2WD/4WD bracket above the drive shaft...and move it out of the way ... You will then have room to move the rear of the drive shaft UP and drop the front of the drive shaft... When I got the 06...- daves06lrenegade
- Post #8
- Forum: KJ General Discussion
-
D
Jeep starts, won't stay running
Hi Hannah... There are a lot of OBDII devices on ebay that are very cheap.... If you have an Android Phone (or an iPhone) that has bluetooth you can use the below device with an app called "Torque" to read the stored codes and also reset them...- daves06lrenegade
- Post #6
- Forum: KJ General Discussion
-
D
I have a different PCM wiring problem...
I bought a 2006 Jeep Liberty Renegade (gas engine 3.7L) as salvage.... There was a fire under the center hump and the wiring harness was burnt in that area... I have been busy attempting to replace the damaged area of the harness... I have come to find that the four PCM connectors do not...- daves06lrenegade
- Thread
- Replies: 1
- Forum: KJ General Discussion
-
D
Does anyone have the pinouts for the PCM 2006 Liberty
Thank You to all who answered my request... 04Liberty your link to the 2005 Jeep KJ was what I needed... After plugging away with this PDF I was able to locate the wiring information and the color codes and was able to identify the C1/C2//C3/C4 locations and colors for the PCM... With the...- daves06lrenegade
- Post #5
- Forum: KJ General Discussion
-
D
Does anyone have the pinouts for the PCM 2006 Liberty
Thank you for taking the time to do some research... It seams I have a "wiring" PDF (8W-) for your diesel engines and not the gas version... If the connector C4 (Black/Green) is actually for the gas version transmission control you may have helped me locate where the wiring harness from the...- daves06lrenegade
- Post #3
- Forum: KJ General Discussion
-
D
Does anyone have the pinouts for the PCM 2006 Liberty
Ref: 2006 Jeep Liberty Renegade I have been searching through the Jeep liberty service manual and also found the electrical (wiring) portion separate from the service manual on ScribD... It looks like the TCM is located within the PCM on the GAS engine versions... I have found the...- daves06lrenegade
- Thread
- Replies: 4
- Forum: KJ General Discussion
