New bumper

[DoverKJ]

I havent been on LOST for awhile and didnt realize it was down until today, then started going trhough the other sites I was registered on to see what was going on. Well since I am the site I might as well post up pix of my new front bumper.

You must be registered for see images attach

You must be registered for see images attach

 

[fulltimer]

Looking good! Did you make it?

Terry

 

[DoverKJ]

I had a custom bumper fabricator make it. I wish I could of made it myself but I dont know how to weld nor do I have the time to learn at the moment.

 

[501]

Looks good Dover!

 

[Dave]

Looks really nice. I like the receiver in the middle too. Now you need a shackle for it.

Dave

 

[riptricket]

awesome bumper!!!
Are those led lights?
How much did it cost?


FREAKIN' AWESOME!!!!!!

 

[fouros]

where did you relocate the washer bottle too?

 

[Drucifer]

I havent been on LOST for awhile and didnt realize it was down until today, . . .

You'll find that most active L.O.S.T. members have found there way here.

Can't see the tow hooks in your pictures. Are they still there?

 

[jsc7002]

looks good, what thickness is the material its made from?

 

[DoverKJ]

I havent relocated the washer bottle yet, running without at the moment.

They are not LED's yet, but I am planning on changing out to LED because the turn signal is just not bright enough.

Tow hooks are gone, have the clevis tabs for the d-rings and will probably get another receiver shackle to have three tow point on the front. The bumper re-uses the holes for the two hooks, so in theory I could put them back on if I wanted too.

The main bumper is 3/16" and the light bucket area is 1/8". There is 1/4" angle iron mounting it to inside the uniframe rails with grade 8 bolts to secure it.

 

[jeepkj02]

Dover, the bumper look great!! Need to get some d-ring shackles to finish it off. If you'd like I can take a picture of where I relocated the washer bottle, won't be able to post the pics until later today.

 

[DoverKJ]

That would be great. Also maybe what you used for a bottle as well. LOST had a post about some custom washer bottles, but i cannot remember the site. They were a bit more expensive then the autozone overflow bottle, but the pump hooked right up.

 

[ga_repoman]

tell you buddy that if he could turn them out i bet he could sell a couple to lost members

looks really good now go test it out tow a truck or hit a tree with it

 

[jeepkj02]

I just use a coolant bottle from advance auto. It was pretty cheap. Used a hole saw to mount the pump. Used some RTV on the rubber gasket to seal the pump. Extended the wiring and filled the bottle.

Here is the bottle I used.

1.5QT Coolant Bottle

 

[Maximum Carnage]

Nice bumper, what did it cost you?

 

[DoverKJ]

I got a very good deal on the bumper, way lower then he should have sold it for, but he quoted me a price and stuck too it. He ran into several problems while making the bumper including the front end on my jeep is not square and the left and rights sides are not the same. He said that this is not a problem limited to just KJ, but Grands and Cherokees have the same problems.

 

[dog_party]

Very nice bumper! Definitely tell this person that there is a potential buying market for his bumper!

 

[jeepkj02]

Sorry for the delay in pics:

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

 

[tommudd]

Sorry for the delay in pics:

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

nice looking job!!!

 

[tommudd]

I havent relocated the washer bottle yet, running without at the moment.

They are not LED's yet, but I am planning on changing out to LED because the turn signal is just not bright enough.

Tow hooks are gone, have the clevis tabs for the d-rings and will probably get another receiver shackle to have three tow point on the front. The bumper re-uses the holes for the two hooks, so in theory I could put them back on if I wanted too.

The main bumper is 3/16" and the light bucket area is 1/8". There is 1/4" angle iron mounting it to inside the uniframe rails with grade 8 bolts to secure it.

How is it bolted on and with how many bolts ?
Thanks

Tom