Search results
-
Bank 1 sensor 1 wiring 2007 Liberty Sport
I recommend downloading the 2007 service manual to avoid mistakes. There is a diagram like the one I attached at the back of the wiring section.- ikuo78
- Post #5
- Forum: KJ General Discussion
-
Do I have the parts correct for my lift kit and what is the difference between front and rear height
That's a good plan. Leveling depends on the weight of the equipment, so you won't know until you lift it. If the front is higher than the rear, it will be complicated.- ikuo78
- Post #11
- Forum: KJ General Discussion
-
Do I have the parts correct for my lift kit and what is the difference between front and rear height
I feel that 790 is too stiff for vehicles without a winch or steel bumper. It looks like it's going to lift about 4 inches with the suspension remaining extended and barely moving. I haven't actually experienced it, just my impressions from looking at the specs.- ikuo78
- Post #6
- Forum: KJ General Discussion
-
Bank 1 sensor 1 wiring 2007 Liberty Sport
Excerpt from the 2003 service manual.- ikuo78
- Post #2
- Forum: KJ General Discussion
-
Project to divert KK coil to KJ
The rear shocks arrived and I installed them. Without removing the tires, Without jacking, Crawling under the car, It was frustrating to put 3 t1 washers in this location. It is better to use only one t3 washer. It took about 45 minutes to complete, so it may have been faster than removing the...- ikuo78
- Post #18
- Forum: Members' Journals
-
Misfire 2 & 6
The translation is strange. The meaning is as follows. If #6 is actually misfiring, It is very unlikely that it is due to the sliding resistance of #2 and #4.- ikuo78
- Post #16
- Forum: KJ General Discussion
-
Misfire 2 & 6
Checking fuel flow is a good idea. Certainly, if #6 is actually misfiring, there is little doubt that it is due to the sliding resistance of #2 and #4. I don't know if there is a possibility of injector shutoff due to false misfire judgment. The following are additional points that are likely...- ikuo78
- Post #15
- Forum: KJ General Discussion
-
Misfire 2 & 6
Does it feel like it's actually misfiring? If compression is low, the piston rings or liner may be damaged. Depending on the circumstances when the gasket was damaged, they may be damaged. In the worst case, if water hammer occurs, the connecting rod will also bend.- ikuo78
- Post #13
- Forum: KJ General Discussion
-
-
Project to divert KK coil to KJ
Dodge Dakota 4x4 rear shocks. I learned that it can be used here. The Rnccho RS5248 I looked for while looking at the SPEC table is for Dakota, so I'm sure. RS5248 is out of stock and probably not manufactured. So, I ordered A-premium ones from Amazon.com. This is a dubious product. There are no...- ikuo78
- Post #17
- Forum: Members' Journals
-
Misfire 2 & 6
Although it may have been replaced, the altitude value measured by the MAP sensor is also recalled from memory at startup. I'm not sure if there was any other memory to accumulate. It seems that some accumulated memory is inappropriate on cold start. If the O2 sensor is not genuine, it is...- ikuo78
- Post #8
- Forum: KJ General Discussion
-
Misfire 2 & 6
What is the long term fuel trim value? The head gasket comes out. →A large amount of water vapor is emitted. →The O2 sensor is damaged. (O2 sensor is sensitive to moisture) →Fuel trim goes out of order. → Trim returns by resetting the ECU.- ikuo78
- Post #5
- Forum: KJ General Discussion
-
Misfire 2 & 6
If you turn the key on and off several times before starting the car, will it no longer misfire?- ikuo78
- Post #4
- Forum: KJ General Discussion
-
Misfire 2 & 6
Are the 2nd and 3rd times a cold start or a hot start? There are certainly some car models that shut off the injector of the problematic cylinder when there is a problem with the ignition coil. In that case, if you unwire the coil while idling, the misfire will still occur even if you wire the...- ikuo78
- Post #2
- Forum: KJ General Discussion
-
Muffler nuts What Muffler nuts
If you can use the nut that fixes the pipe hanger bracket near the catalyst to the transmission as is, it will be M8xP1.25.- ikuo78
- Post #4
- Forum: KJ General Discussion
-
Project to divert KK coil to KJ
Finally, a cool, non-rainy weekend arrived, so I assembled the struts to the car body. It was a bit difficult to remove the old struts that had over 40mm spacers in them. I was able to easily insert the spring compressor on the right side, but on the left side, I had to redo it many times and...- ikuo78
- Post #16
- Forum: Members' Journals
-
Overhead console is dead
The power supply looks like C308 connector No.3 and No.5. No.3→Always No.5→RUN/ON Maybe. I can't remember if I was able to turn it on or off with a button somewhere.- ikuo78
- Post #4
- Forum: KJ General Discussion
-
Overhead console is dead
If you do something that causes the fuse to blow, it won't go away unless you remove it. However, it seems that there is another fuse in the junction block that is always energized. From the 2003 manual.- ikuo78
- Post #2
- Forum: KJ General Discussion
-
A Driver's side Thunking Mystery
Something seems to be loosely mounted. Does it depend on throttle? Does it depend on the bumps in the road? The key to solving this problem is the conditions under which the sound occurs.- ikuo78
- Post #2
- Forum: KJ General Discussion
-
Need help with parasitic draw on my 2005 CRD
I think you can find circuits that are consuming power by removing suspect always-on fuses one by one and reading the change in dark current, as you did with the junction box. If you are concerned about the current value of the interior light, remove the interior light bulb. If you disconnect...- ikuo78
- Post #6
- Forum: KJ General Discussion
