Search results

  1. ltd02

    K&N Cold Air Intake

    I've run an AEM brute force CAI (dry cone filter) for 15 years and over 120k in my 4.0L OHV ranger and never had an issue with my engine (187k now). I do run a hydrophobic prefilter and the kit does come with a box setup that draws air from around the headlight and grill, not just sucking hot...
  2. ltd02

    Wheel bearing dead

    Ahh yes, I remember your dilemma. Good luck with that! I hate when those little thing gum up the works.
  3. ltd02

    Wheel bearing dead

    Did you rotate the tires yet?
  4. ltd02

    Parking lot

    Trees are growing back! That tornado was a doozy. Changed the whole park. Coin op hot water is still there and the showers are open again after the COVID shutdown. We have a cabin nearby and I've been going to that park since 1966. I've seen it all.
  5. ltd02

    Parking lot

    Nice! I'm originally a PA guy from the Scranton area. I've been to Ricketts several times over the years. The Milford PA Gifford estate (Grey Towers) is awesome! Those giant European Beech trees. Haven't been to the park near York. Heading to Promised Land tomorrow.
  6. ltd02

    Parking lot

    That's an awesome setup! What campground were those pics taken?
  7. ltd02

    PCV valve not all the way in, would this be okay? Code P507

    Yeah, forgot the TPS and IAC are integral parts of the TB in the 07-12. You have to replace the whole TB. I don't think they are serviceable.
  8. ltd02

    PCV valve not all the way in, would this be okay? Code P507

    Not very familiar with the 07 but did do an 07 PCV swap on my 02 years ago. The 02 has a breather in the 07 PCV spot that's threaded just the same though. Mine stuck out a bit too when tight so I don't think they go in very far. I had a very big deep socket to install mine but the adjustable...
  9. ltd02

    3.7 knock?

    Did you ever cut open an oil filter and see if there is any bearing material in the folds? Look for bits in the drained oil too. Use a paint filter. I spun a #2 rod bearing around 175k in my 02. Knocked for quite a few months before it went.
  10. ltd02

    What did you do to your jeep today?

    I was waiting for the part where you ran him and his motorcycle over while moving it into the sun...
  11. ltd02

    How to: Replace HVAC blend door actuator

    Does the range work from full open to full closed or did you have to run a calibration?
  12. ltd02

    2004 Jeep Liberty (current: Engine Swap)

    It's probably just a bit crusty there. The clamp has to be removed from the joint as it is still holding the pipes together even without the bolt. I just pried at it with a long screwdriver. Start at the opening and it should slide up or down. Even with the bolt out like your's there is a good...
  13. ltd02

    What did you do to your jeep today?

    Here's your assignment for your day off: Check it under all three conditions and report back... ;)
  14. ltd02

    Correct blend door actuator?

    Sounds like the actuator may be working correctly. Mine would only run in one direction and stutter and stop in the other. If yours worked smooth in both directions (switching polarity) when off the door post then more likely the blend doors are binding. I thought the blend switch sets the...
  15. ltd02

    How to: Replace HVAC blend door actuator

    Mine failed on the cold setting and I believe it is default for the system and the motor/actuator. I think every time you shut the engine off the blend doors move to cold and then reset to previous dial setting when you start up again. I guess I was lucky since it fit right on and lined up. I...
  16. ltd02

    What did you do to your jeep today?

    You can buy that loom material that looks just like the OE corrugated tube stuff. It will have a slit in it to allow you to slide it over the wire bundle. makes it look pretty factory. I have rolls of a few different diameters out in the garage. There is a cloth like tape for looms that makes...
  17. ltd02

    What did you do to your jeep today?

    If you can figure out the size, check here: https://www.clipsandfasteners.com/u-clips-nuts-and-fasteners-s/115.htm
  18. ltd02

    What did you do to your jeep today?

    I've had the Battery Tender variety before but had two fail after about 4 years (I guess they do that). They worked great until they quit so not knocking their function. I've had a batteryMINDer for almost 5 years now and really like it. Also has the pulse mode for desulfation. Don't know if...
  19. ltd02

    Is this "too hot"?

    Never had a vehicle heat up as quickly and give good vent heat as my KJs. Must be a good system.
  20. ltd02

    What did you do to your jeep today?

    To quote Bocephus: A country boy can survive.

Random media

My first born my wife and i
Back yard
IMG00027 20090327 1421 Added my hitch step/bumper , a little more bumper protection for the cheap plastic bumpers.
The damage that bought me an ARB
DSCN9174
DSC01567
after doing donuts in the parking lot at the provincial park
PML transmission pan.jpeg
The tax deduction

Latest posts

Members online

Total: 292 (members: 2, guests: 290)
Top