Search results
-
2002 Liberty -$2000 obo
Thank you Dave. This site has made a good few years of wheeling a truly underrated Jeep possible.- ridenby
- Post #7
- Forum: For Sale Forum
-
2002 Liberty -$2000 obo
It is a whole housing and gears,I had it shipped from AZ. Think it weighs less than 50lbs.- ridenby
- Post #3
- Forum: For Sale Forum
-
2002 Liberty -$2000 obo
2002 Jeep Liberty 4x4 No time to wheel,hate to part with Libby. Also have (1) front D30a 3,73 ratio (1) front D30a 4.10ratio $200ea (1) D30 Tru-Trac $200 (1) steering rack $200 (1) intermediate shaft $100 Bunch of other stuff I will list after sorting-ball joints-tie rods-axle bearings...- ridenby
- Thread
- Replies: 7
- Forum: For Sale Forum
-
-
JBA Steel diff. info wanted
IFS is soooo pricey. Currie Enterprises Racing Rear End Categories Ultimate CV Axles for Straight Axles - RCV Off-Road Performance Products - CV Joints, Axle Kits, Tools 5 Lug Drive Flange Kit And a bunch of fabing needed. Yello I expect to see some cool pics of fronts smoking,etc.- ridenby
- Post #11
- Forum: KJ General Discussion
-
JBA Steel diff. info wanted
I can see that. I have no mod to front. Have seen a few bust. knock on wood,I have had 0 problem from mine. Just find it weird that there are NO big write ups about how great the 5000 dollar diff is.- ridenby
- Post #5
- Forum: KJ General Discussion
-
JBA Steel diff. info wanted
I don't care so much if you just Mall Crawl as spending BIG bucks on this kind of thing and no real results shown. I think your numbers are close and I think there are more cost effective solutions. Buy two or three spare diffs(alum) .- ridenby
- Post #3
- Forum: KJ General Discussion
-
JBA Steel diff. info wanted
Wonder where the pics/tales of 33+ tires and beat downs are??? Have only Mall Crawlers bought these things?? Is SFA the only way?? Are CV's holding up to them?? Where is the info??? Smoke and mirrors??- ridenby
- Thread
- Replies: 12
- Forum: KJ General Discussion
-
-
-
What did you do to your jeep today?
looked at her with sad eyes and bright thoughts for future.- ridenby
- Post #624
- Forum: KJ General Discussion
-
Rims and tires with pics!
245/75/16 NO lift,back of wheel well plastic covering pinch weld. DSCN0237 by ridenby, on Flickr 245/75/16 right after Frankie install DSCN0522 by ridenby, on Flickr- ridenby
- Post #10
- Forum: Tires / Wheels
-
Gonna go Wheelin 26-28 Oct.
Going Wheeling at Dirty Turtle,might hit Horseshoe bend too. D.T. is haveing the Tanners come up to try the bounty hills,one hell of a show. Good time to be had if anyone cares to drop by. :smokin:- ridenby
- Thread
- Replies: 1
- Forum: Serious Offroad Trips, Trail Rides, and Meets
-
Gear Oil selection
Switched to dino with my Aussie,took a lot of the pop,bang out of it.- ridenby
- Post #8
- Forum: KJ General Discussion
-
-
Newby?
How to measure: http://www.jeepkj.com/forum/f203/actual-lift-amount-lets-compare-fender-heights-39094/- ridenby
- Post #7
- Forum: Tires / Wheels
-
Location of the Low-Side Service Port (2004, 3.7L Jeep Liberty)
It is the only one that the charge hose will fit.- ridenby
- Post #2
- Forum: CRD KJ's Section
-
Newby?
That is a 29in tire,9in wide. Your choice of wheels is too wide for the tire.I used the same size wheel with 31/11.5/15 tires and they where too wide for them. The tire you are looking at will work on the stock wheel,though it is border line wide for that size tire.- ridenby
- Post #2
- Forum: Tires / Wheels
-
Should I lift my KJ?
I think that upgrading a few things helps.Ever seen a Liberty carry the front wheels up a hill?- ridenby
- Post #17
- Forum: Lift Kit Discussion
-
What did you do to your jeep today?
Replaced radiator that started leaking while Libby sat. Put skids and winch back on. Cleaned mud out of rotors,calipers.- ridenby
- Post #603
- Forum: KJ General Discussion
