Clunk going over bumps on 06

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

alphatoad

New Member
Joined
Sep 27, 2019
Messages
2
Reaction score
0
I have an 2006 and have this clunk that happens sometimes when you go over a bump. It's somewhat harsh when it happens. I have replaced the front coils (shock and spring), front endlinks, front sway bar bushings, rear upper control arm, rear lower control arms, rear shocks. The rear spring perches look fine. I am sitting here scratching my head.
 

tommudd

Moderator
Staff member
Moderator
Joined
Jul 14, 2005
Messages
22,450
Reaction score
3,649
Location
Southeastern Ohio
How are the ball joints ( upper and lower ) ?
Usually it is the sway bar bushings but seems you have addressed most of the things I would of suggested
What front coils and shocks did you use?
Some of the cheaper ones, well most of them allow the suspension to hit the bumpstops even when new , check to see if you can tell if that is the case
 

alphatoad

New Member
Joined
Sep 27, 2019
Messages
2
Reaction score
0
How are the ball joints ( upper and lower ) ?
Usually it is the sway bar bushings but seems you have addressed most of the things I would of suggested
What front coils and shocks did you use?
Some of the cheaper ones, well most of them allow the suspension to hit the bumpstops even when new , check to see if you can tell if that is the case
I used Monroe. I know they aren't high end, but should be ok. There doesn't seem to be any wear on the bump stops (they were replaced). The balls joints all look ok. The rear upper was replaced. Thank you for the suggestions. I'm at a loss. I'm a VW guy so some go the suspension geometry is off, but enough carries over lol.
 

tommudd

Moderator
Staff member
Moderator
Joined
Jul 14, 2005
Messages
22,450
Reaction score
3,649
Location
Southeastern Ohio
I used Monroe. I know they aren't high end, but should be ok. There doesn't seem to be any wear on the bump stops (they were replaced). The balls joints all look ok. The rear upper was replaced. Thank you for the suggestions. I'm at a loss. I'm a VW guy so some go the suspension geometry is off, but enough carries over lol.
Monroe will bounce off the bumpstops making a noise for sure
I installed a full set on a customers , soon after he complained about strange noises. and yes, it was bouncing off the bumpstops
2 hours later was ordering a full OME setup and then he was a happy camper
That was 9 years ago and still have the whole setup laying around, maybe 175-200 miles on them LOL :)
 

jp7794

Full Access Member
Joined
Jun 15, 2009
Messages
64
Reaction score
11
I have somewhat the same issue with a creaking sound coming from the rear when going over sloped curves and bumps. Thinking it is the rear stabilizer bushings. Project for next spring as we just had our first snow.
 

HoosierJeeper

Gold Supporter/Admin
Staff member
Administrator
Joined
Jan 20, 2009
Messages
20,874
Reaction score
299
Location
Western WI
I have somewhat the same issue with a creaking sound coming from the rear when going over sloped curves and bumps. Thinking it is the rear stabilizer bushings. Project for next spring as we just had our first snow.
No rear sway bar bushings on the KJ. Mine had some creaking from the rear and it was just sand/mud caught in the LCA bushings. cleaned it up and it's quiet.

OP, what happens when you go like 5MPH and slam on the brakes? if it pops then, the lower control arm bushings are probably shot.
 

tommudd

Moderator
Staff member
Moderator
Joined
Jul 14, 2005
Messages
22,450
Reaction score
3,649
Location
Southeastern Ohio
I have somewhat the same issue with a creaking sound coming from the rear when going over sloped curves and bumps. Thinking it is the rear stabilizer bushings. Project for next spring as we just had our first snow.
No stabilizer bar on the KJ
So it more than likely the upper control arm bushings or the lower control arms going bad
also check the upper bolts on the rear shocks , I've seen them back off just enough to make creaking sounds and it doesn't take much, sometimes 1/8 to 1/4 turn
 

Latest posts

Members online

Top