Who makes a good quality durable cv axel?

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

Zippy the jeep

New Member
Joined
Dec 8, 2021
Messages
11
Reaction score
0
Ok i replaced both my cv axels with mopar original axels 8 months ago, one has failed , went back to jeep they said they have zero in country . So now i am having to find an aftermarket on , so i found “RUSTY’S offroad” in Tennesse and they said oh yea all made in america so i said great i ordered one and come to find out they just sold me a “Crown” one which is made in china , so i cancelled my order. Does anyone know where i can get a good quality durable cv axel made here in america ? its for a 2006 liberty passenger side.. dont care about the cost , i just need a good quality durable axel..
 

JeepJeepster

Full Access Member
Joined
Dec 15, 2004
Messages
8,932
Reaction score
327
Location
Dem hollers in Ky
What happened to the mopar unit? Very odd for a new mopar CV to go bad that quickly.

Typically a Napa reman unit is recommended. Had one on my KJ for around 14 years.
 

tommudd

Moderator
Staff member
Moderator
Joined
Jul 14, 2005
Messages
22,450
Reaction score
3,650
Location
Southeastern Ohio
I only use NAPA remanned
Have replaced a ton of them over the years in various friends, customers KJs and never any issues at all
 

Zippy the jeep

New Member
Joined
Dec 8, 2021
Messages
11
Reaction score
0
What happened to the mopar unit? Very odd for a new mopar CV to go bad that quickly.

Typically a Napa reman unit is recommended. Had one on my KJ for around 14 years.
The boot dry rotted and cracked and let all the grease out in 8 months believe it or not . So Jeep is paying for the replacement so i am looking for a good made in america replacement one .. I can’t believe Mopar/Jeep has none in the US , what is this country coming to…
 

Zippy the jeep

New Member
Joined
Dec 8, 2021
Messages
11
Reaction score
0
I only use NAPA remanned
Have replaced a ton of them over the years in various friends, customers KJs and never any issues at all
Thanks ill give them a look , are they American made parts in the axels ?
 

tommudd

Moderator
Staff member
Moderator
Joined
Jul 14, 2005
Messages
22,450
Reaction score
3,650
Location
Southeastern Ohio
I will NEVER reuse an intermediate shaft always replace with a new one due to wear
I have some piled up with only 20,000 miles and won't use them again
Also unless its a very low mileage CV I would never use a used one especially on a KJ due to age etc when you can buy a remanned for 60 bucks or so with a trade in
 

lfhoward

Wheel. Repair. Repeat.
KJ Supporting Member
Joined
Dec 9, 2012
Messages
2,449
Reaction score
2,710
Location
Philadelphia, PA
I will NEVER reuse an intermediate shaft always replace with a new one due to wear
I have some piled up with only 20,000 miles and won't use them again
Also unless its a very low mileage CV I would never use a used one especially on a KJ due to age etc when you can buy a remanned for 60 bucks or so with a trade in
Good to know. I think my junkyard CV had only 20K on it and I got the intermediate shaft with it as a matched set. Back then (~2014) Napa had no remanned KK CV’s in stock nationwide. Hope they do by now.
 

Zippy the jeep

New Member
Joined
Dec 8, 2021
Messages
11
Reaction score
0
I will NEVER reuse an intermediate shaft always replace with a new one due to wear
I have some piled up with only 20,000 miles and won't use them again
Also unless its a very low mileage CV I would never use a used one especially on a KJ due to age etc when you can buy a remanned for 60 bucks or so with a trade in
Yea i agree 100% i never would either , **** i wont even install a cheap china one .. is napa reman made in america? Do they use American parts to reman them ?
 

tommudd

Moderator
Staff member
Moderator
Joined
Jul 14, 2005
Messages
22,450
Reaction score
3,650
Location
Southeastern Ohio
Yea i agree 100% i never would either , **** i wont even install a cheap china one .. is napa reman made in america? Do they use American parts to reman them ?
answered above but yes they are
intermediate shafts are scarce at times so you may want to start looking for one
 

JeepinJarhead03

Full Access Member
Joined
Sep 17, 2009
Messages
387
Reaction score
16
Location
Petersburg VA
X2 on Napa cv remans, I also use their replacement boots, I occasionally tear mine down and clean them out and repack them, the outer cv rzeppas in particular benefit from getting cleaned out and repacked every 15k or so, their because of their type they don't circulate grease very well
 

Latest posts

Top