Search results
-
What did you do to your jeep today?
bolt-06507275AA nut-06102251AA Gyro- Gyro
- Post #20,014
- Forum: KJ General Discussion
-
-
NV/NP-231-J Help
A couple I googled https://www.morris4x4center.com/np-231-transfer-case-parts.html https://www.quadratec.com/jeep-replacement-parts/wrangler-tj/tj-np231.php Gyro- Gyro
- Post #2
- Forum: KJ General Discussion
-
the firewall rubber grommet..I think this is it?
yes top left in the pic. -
the firewall rubber grommet..I think this is it?
If you are tying to run wires,just run them through the main harness grommet. That's how I ran wires. Gyro -
Fitment help: 265/70 on 16x8 with 0mm offset, 2.5" lift
Here is a link to some Moab replicas in Canada- https://www.tdotperformance.ca/mamba-mr1x-series-wheels.html Gyro- Gyro
- Post #5
- Forum: Tires / Wheels
-
Wiring from engine bay to inside (Dash)
Just above the drivers side kick panel (where hood release is) where the main harness comes through the fire wall is where I ran some wires. I used a coat hanger to fish them from the inside to engine bay.- Gyro
- Post #2
- Forum: KJ General Discussion
-
Rear glass lift struts - bracket
I got ball studs for my 06 here- http://lstechnologies.ca/ SW7M5 is the size I used.search in mounts and brackets. Gyro- Gyro
- Post #3
- Forum: KJ General Discussion
-
2007 Jeep rear end rumble?
The rear cv is the one that usually goes when the boot fails. Link to rear cv rebuilt kit- https://www.driveshaftparts.com/index.php?route=product/product&path=174&product_id=978 Gyro- Gyro
- Post #16
- Forum: KJ General Discussion
-
Aftermarket fender flares
Are we talking front,rear or both. Are you using wheel spacers,oversize tires,are you lifted,do you have the proper bumpstops? Gyro- Gyro
- Post #2
- Forum: KK General Discussion
-
Suspension, Front and Strut Parts Question
Front and rear stud spacing on the upper mount is the difference. https://jeepinbyal.com/jba-strut-spacer-plate-set-kj-kk.html Gyro- Gyro
- Post #2
- Forum: Lift Kit Discussion
-
Engine Coolant Temperature (ECT) sensor - Help with location
It should be located just behind the alternator,screws vertically into engine block. looks like this https://www.napaonline.com/en/p/ECHTS5805?searchCategory=c5.s4&searchIndex=Universal Gyro- Gyro
- Post #2
- Forum: KK General Discussion
-
KL Cherokee transmission recall
KL Cherokee transmission recall . https://www.bnnbloomberg.ca/fiat-chrysler-recalling-almost-95-000-jeep-cherokees-1.1452581 Gyro- Gyro
- Thread
- Replies: 0
- Forum: Technical Service Bulletins and Recalls
-
Cross Canada trip in an 03 Liberty with an RV.
Bring a gas can,there are some good stretches with no services. I always take hiway 11(northern TC route from North Bay)it's straighter and flatter for the most part. Gyro- Gyro
- Post #4
- Forum: KJ General Discussion
-
How does OME handle washboard roads?
I have run both. If you run mostly empty 926,if you run with a load 927. Even a light load will smooth out the ride of the either. Gyro- Gyro
- Post #16
- Forum: Lift Kit Discussion
-
Blower motor resistor
See here: https://www.jeepkj.com/threads/blower-motor-resistor-upgrade-for-kj.65152/ Gyro- Gyro
- Post #2
- Forum: KJ General Discussion
-
PCV valve not all the way in, would this be okay? Code P507
Mine is the same, about 1/2in of thread showing. I got a large socket to do mine,eezy peezy. Gyro- Gyro
- Post #3
- Forum: KJ General Discussion
-
What did you do to your jeep today?
Don't have alot kms on them yet,but seems a little more peppy at take off and rpm is a little lower at 80kph OD off. And the speedo seems a little closer to actual. Gyro- Gyro
- Post #19,803
- Forum: KJ General Discussion
-
Renegade Rail Bolts to frame nuts needed
Try searching hex rivnut. https://www.rivetsinstock.com/rivet-nuts-threaded-inserts/half-hex-body-rivet-nuts.html Gyro- Gyro
- Post #7
- Forum: KJ General Discussion
-
What did you do to your jeep today?
5 new KO2's on the 07. Switched from 245/75/16 to 255/70/16.- Gyro
- Post #19,801
- Forum: KJ General Discussion
Members online
No members online now.