Search results
-
-
Has anyone installed a JC Whitney or universal winch plate ? (cheap)
I Used 2x2x1/4 tube to slide in to "frame" and stick welded them. Then added another piece of tube on top of them to raise mounting plate height. Drilled some holes for grade 8 1/2in bolts to hold plate on. Plate came from Harbor Freight,$35 I think. Used a 12,500lbs winch from Tuff Stuff...- ridenby
- Post #5
- Forum: KJ General Discussion
-
-
-
Chain Jingle Sound While Driving
Yes that is the correct one.- ridenby
- Post #18
- Forum: KJ General Discussion
-
Question ? 15 x 7 w/ 31 10.5 x 15 work ?
Regardless,you and your jeep will be happier with 16" wheels. 15" works,it is just so close to rubbing the caliper.- ridenby
- Post #4
- Forum: Tires / Wheels
-
kj auto lockers
Open front,never got a round toit. Yes,Aussie is loud at times. If you want quiet,smooth,go LSD rear. Front too,if you think you really need it.- ridenby
- Post #4
- Forum: KJ General Discussion
-
Rebuild kits for front drive shafts
What I thought Tom. I do like joints,high speed or otherwise.- ridenby
- Post #3
- Forum: KJ General Discussion
-
kj auto lockers
Used an Aussie,it worked. Easy install,as are all the lunchbox lockers. Use 80-140 gear lube.- ridenby
- Post #2
- Forum: KJ General Discussion
-
Rebuild kits for front drive shafts
Ran across another source of front drive shaft C.V. joint repair kits. Results for Jeep High Speed Joints:Liberty- ridenby
- Thread
- cvs front drive shaft repair kit
- Replies: 2
- Forum: KJ General Discussion
-
broke off oil pan bolt head
Left handed drill bits. Remove a broken bolt using a left handed drill bit - YouTube- ridenby
- Post #5
- Forum: KJ General Discussion
-
-
Adding 2 1/2 inch spacer lift, biggest tire avalible w/o rubbing?
OP,I know you do not believe the Rev.,though he is telling the straight of it. Check through the 1000+ threads on this very subject. Many have used the spacers just to swap out to springs and shocks shortly afterward. Save some time,spend your money once,do it right.- ridenby
- Post #9
- Forum: Tires / Wheels
-
Power Steering Pressure Line Leak?
If the leak is at hose end where it goes into pump or rack,I would replace "O" ring first. NAPA has the right size,can not recall it off the top of my head.- ridenby
- Post #5
- Forum: KJ General Discussion
-
no one can figure out my KJ noise
Put it on a lift,have someone run it up to where the noise occurs. You will be able to pin point it.- ridenby
- Post #8
- Forum: KJ General Discussion
-
battery tray upgrade
I used an Optima 34/78 , changed ends on wires to ring type,attached to the side terminals.Used the posts for winch cable attachment. Remove the tray and trim edge next to inner fender.- ridenby
- Post #6
- Forum: KJ General Discussion
-
Intermediate Shaft Still Available from NAPA?
Hit it with your purse,Mary. Do as Tom says,Vise grips,and jerk it out. The CV axle came off? If so it can be a bugger to get out but it will come.- ridenby
- Post #21
- Forum: KJ General Discussion
-
ECS- Saturday
Too cool. At first I thought hell had surly froze over,HJ out in the woods. And Blue Bunnie up and going.- ridenby
- Post #4
- Forum: Post Your Liberty Pictures
-
replacement radiator
http://www.buyaradiator.com/kresults.html?t=Radiator&y=2002&ma=JEEP&mo=LIBERTY&e=3.7 RadiatorBarn.com has sold to keystone something or another. I guess these will be same mfg.- ridenby
- Post #2
- Forum: KJ General Discussion
-
Help - Got jack stuck under vehicle
This might be the funnest thing I have read this week. Would like to have seen your face when you saw what was going on there!- ridenby
- Post #10
- Forum: KJ General Discussion
