What did you do to your jeep today?
- Thread starter TheQ
- Start date
Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.
wheeee32
Full Access Member
Prepped the rear bilstein shocks to be installed by using a vice at work to press the sleeves into both ends.
Btownpreacher
Full Access Member
- Joined
- Nov 13, 2022
- Messages
- 132
- Reaction score
- 104
Been super busy the last few days, haven't quite finished my transmission skid plate, but I do have it mounted. I'll be adding some brackets and gussets to make it worthy of carrying my KJ over the trails. I'm still looking to level my Liberty; I've installed the OME Springs and shocks, I believe they were 2927 and 2948. After a few thousand miles I'm at 21.75" in the rear and 20.75" in the front. How high do I have to be to run 245/75/16? And what do I use to lift the front? I can't seem to find the kk clevis/forks conversion; also heard to use conduit nuts? I don't even know what they are, never mind where do I find them?!? 
Anything else that I can use?
Anything else that I can use?
information regarding this can be found here: JBA strut spacer or clevis spacer?
as far as I can see, JBA does no longer sell clevis spacers nor upper plates, but you can do without them Clevis spacers), they are used only for exact measurement
as far as I can see, JBA does no longer sell clevis spacers nor upper plates, but you can do without them Clevis spacers), they are used only for exact measurement
Any chance of a picture of your skid plate?Been super busy the last few days, haven't quite finished my transmission skid plate, but I do have it mounted. I'll be adding some brackets and gussets to make it worthy of carrying my KJ over the trails. I'm still looking to level my Liberty; I've installed the OME Springs and shocks, I believe they were 2927 and 2948. After a few thousand miles I'm at 21.75" in the rear and 20.75" in the front. How high do I have to be to run 245/75/16? And what do I use to lift the front? I can't seem to find the kk clevis/forks conversion; also heard to use conduit nuts? I don't even know what they are, never mind where do I find them?!?
should only of been one end
On the front , just loosen clevis bolt, using the end of a 3/8 inch extension, raise that amount and tighten down and doneBeen super busy the last few days, haven't quite finished my transmission skid plate, but I do have it mounted. I'll be adding some brackets and gussets to make it worthy of carrying my KJ over the trails. I'm still looking to level my Liberty; I've installed the OME Springs and shocks, I believe they were 2927 and 2948. After a few thousand miles I'm at 21.75" in the rear and 20.75" in the front. How high do I have to be to run 245/75/16? And what do I use to lift the front? I can't seem to find the kk clevis/forks conversion; also heard to use conduit nuts? I don't even know what they are, never mind where do I find them?!?
sleazy rider
Retired moto tech and gearhead
Washed and waxed the Wrangler to deny the bugs a grip on the 1300 mile drive home in a couple weeks. Having 4WP remove, clean and grease the spare tire bumper swing arm. It done got fightin’ tight.
Btownpreacher
Full Access Member
- Joined
- Nov 13, 2022
- Messages
- 132
- Reaction score
- 104
I'll show you what I've done so far; back in a bit
Btownpreacher
Full Access Member
- Joined
- Nov 13, 2022
- Messages
- 132
- Reaction score
- 104
I just changed out my PCV/CCV valve, the old one was leaking. Also adjusted the clevis position, does this look right? Also, this is the transmission skid plate mounted underneath the Liberty. Big surprise, I'm sitting at 21.75" at all for corners. Now the big question: Is that enough to run 245/75/16 on stock wheels?!? Another random question, should I get longer sway bar links? If so where from?
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
Btownpreacher
Full Access Member
- Joined
- Nov 13, 2022
- Messages
- 132
- Reaction score
- 104
The skid plate is 1/8" or 11 gauge steel; I'm also using 1/8" thick 1"x1" angle iron for reinforcement, just haven't gotten that far yet. I'll weld it up this week and I'll take more detailed pictures with it off. I'll also try to upload the template that I made so that ya'll can do it to
Thank you! This is the approach I have been thinking of, have some stainless possibly earmarked for the job which already has pressed lightening holes in.The skid plate is 1/8" or 11 gauge steel; I'm also using 1/8" thick 1"x1" angle iron for reinforcement, just haven't gotten that far yet. I'll weld it up this week and I'll take more detailed pictures with it off. I'll also try to upload the template that I made so that ya'll can do it to
No longer sway bar links are needed , I ran over 4.5 inches for way over 100,000 miles with stock length links and no issues at all
Pound over the pinch welds in front and 245-75-16s will be tight but work at 2.75 inches of lift
just be prepared for a little drop in mileage and power
I can almost feel that skid plate bending , at the very least need to add some angle iron front to back and help strengthen it
not near heavy enough to stand up to a rock etc
Jancet
New Member
I replaced the coolant reservoir and thermostat
MOPAR thermostat I hope
duderz7
Full Access Member
Replaced the passenger side o2 sensor yesterday, would be soo much easier if I had hands and arms the size of a 6 month old. Received the rear set today. They were discounted, supposed to be new in opened package. True for one, but the other was obviously used, had broken wire insulation and wasn't even ntk brand. If it was anyone reading this happens to be the one who sends old parts back to Amazon and claims they are unused, you are a tool bag! And I hope you have never ending car troubles, as for the rest of you...many happy days!
Deb'nKJ
Full Access Member
- Joined
- Jun 3, 2022
- Messages
- 634
- Reaction score
- 540
Gaffer tap?
No, seriously, without knowing what the actual problem is, it's difficult to be constructive.
Wouldn't it be easier just to replace it? I mean even on our Septic Isle they can't be so expensive or hard to find - can they?
No, seriously, without knowing what the actual problem is, it's difficult to be constructive.
Wouldn't it be easier just to replace it? I mean even on our Septic Isle they can't be so expensive or hard to find - can they?
I scored a new old stock Miller Tool 8696CC from eBay. I now have all the receiving cups and driver to remove all bushings from my suspension.
In the future, i plan on posting sizes for all the tools for people to make their own.
In the future, i plan on posting sizes for all the tools for people to make their own.
You must be registered for see images attach
Btownpreacher
Full Access Member
- Joined
- Nov 13, 2022
- Messages
- 132
- Reaction score
- 104
Thanks! I'll do that and see how it works.
I've already planned a good bit of reinforcement for the plate, which I started today; I'm hoping to finish it up tomorrow and I'll post final pictures for y'all. I don't really plan to high-center my kj in a rock garden, but I'm dead sure not going to take the risk
