What did you do to your jeep today?

[tommudd]

4 new tires installed this morning
No road noise, feel solid, dig good so far :gr_grin:
(265-70-16 Falken Wild Peak A/T 3 W's )

 

[nohitter64]

Scored some tow hooks at the junk yard, too wet to install them today. Mulling over a cb antenna mount and considering placing a bracket under one of the tailgate hinge bolts. Any thoughts on this approach? Is it a bad idea to mess with the tailgate hinges? The antenna may slightly block the driver tail light.

 

[turblediesel]

Scored some tow hooks at the junk yard, too wet to install them today. Mulling over a cb antenna mount and considering placing a bracket under one of the tailgate hinge bolts. Any thoughts on this approach? Is it a bad idea to mess with the tailgate hinges? The antenna may slightly block the driver tail light.

Best to have an antenna in the middle of the roof. The hinge position you're considering would transmit best toward your RF tire and the antenna would act like it was cut off since it's blocked until it clears the roof.

If the distance you want to talk is not far then almost anything will work.

 

[uss2defiant]

got it aligned.
also while i was replacing my RLCA, I replaced the rear axle breather hose.

oh, does anyone want my old RLCA? I have the beefier style ones.
FOC just pay the shipping

 

[Kim'sJeep]

Went to PnP since they were having a sale. Found a sunroof, roof rack bars (not pictured), evic unit, and a muffler. Installed the muffler today.

You must be registered for see images attach

 

[Jo6pak]

Changed the cabin air filter.
Changed the wiper blades (front and rear)
And swapped the low beam bulbs for Sylvania Silverstars.

 

[tommudd]

Drove it 260 miles or so, new tires are not worn out yet so we shall see :happy175::happy175:

 

[sota]

Napa axle. New or reman?

 

[LibertyTC]

got it aligned.
also while i was replacing my RLCA, I replaced the rear axle breather hose.

oh, does anyone want my old RLCA? I have the beefier style ones.
FOC just pay the shipping

Do you have pics of the old LCA & the new ones that are better?
Was there a cut away in rubber bushings in the new one at axle side?
PICs Please ! :gr_grin:

 

[LibertyTC]

How do you like my new tensioner spray booth ?
62515[/ATTACH]"]

You must be registered for see images attach

While vertical,cover with the cardboard lid & you got dust free drying parts! :gr_grin:
Link: https://www.youtube.com/watch?v=-eZnbIz5gtI

 

[uss2defiant]

Do you have pics of the old LCA & the new ones that are better?
Was there a cut away in rubber bushings in the new one at axle side?
PICs Please ! :gr_grin:

Yes there was. the replacements were exactly the same except for the welding points.
Sorry. no pics of the replacements.

 

[u2slow]

Put in the 242J last night :sawzall:

Full-time mode will be fun this winter. :gr_grin: I'll post up some pics on the swap later.

http://www.jeepkj.com/forum/f196/242j-selec-trac-swap-6spd-64369/

 

[sota]

Put in the 242J last night :sawzall:

Full-time mode will be fun this winter. :gr_grin: I'll post up some pics on the swap later.

and details. like what parts you had to replace to make it fit.

 

[cplchris]

picked up the new heads, timing chain guides, tensioner arms, head gasket set, and head bolts...now i just need new exhaust manifold bolts, the timing lockout tool, assembly lube, and who knows what else. it's going to be a fun weekend.

 

[Whelan]

Diagnosed and in the process of replacing the power seat circuit breaker. Both front seats without power, found the breaker and hoping the $7 part fixes the problem.

Just did oil changes on both cars, and just psyched I got to a point in my experience I can do it easily and in about 10 minutes total, skipping the need to jack up the car and not needing big dip pans to save the floor.

Hoping to get the tri-link mount replaced this week when my neighbors lift opens up.

 

[Joenavy85]

Accidentally bumped the stealth button on my CRD while I was sweeping the shop so I slapped the unmentionable on the exhaust manifold with the gadget from the plumbing aisle. Goobered the v-clamp on it and it seems good even though I can't see it.

Maybe I can put some more parts on it before it "stealths" again.

Feels good to make any progress on it.

Wait......What? I don't have a CRD, so maybe that's why this went completely over my head.

 

[Myke]

Took 2nd place in the car crush & mud pit competition in my XJ.

Outside view video: https://www.instagram.com/p/Bpf4P8KBQHd/

Inside view video: https://drive.google.com/file/d/1owi_sKAeFi03lj4HJ-dHeuk3xD33-hxx/view?usp=drivesdk

Inside view video 2: https://drive.google.com/file/d/1CRviLSJcXvokYgQmLYg3KUc_zvSnx6VS/view?usp=drivesdk

You must be registered for see images

You must be registered for see images

You must be registered for see images

You must be registered for see images

You must be registered for see images

You must be registered for see images

You must be registered for see images attach

You must be registered for see images

You must be registered for see images

Sent from my SM-N950U using Tapatalk

 

[navupmyself]

https://imgur.com/a/bg0Mt4O

Cleaned out my IAC valve. Was having problems with stalling after giving it gas, cleaned this up and now idles great

 

[turblediesel]

Wait......What? I don't have a CRD, so maybe that's why this went completely over my head.

Yup, it's a CRD thing...

 

[tommudd]

Yup, it's a CRD thing...

A Jeep KJ CRD thing, if ya gotta ask.......you wouldn't understand

:happy175::happy175::happy175::happy175: